How To Repair A Window Motor For 1978 Cadillac Seville Youtube.com

Download Commodity

Download Article

If i of the ability windows in your vehicle fails to function, information technology may be the result of a cleaved ability window motor. If you accept identified the motor as the culprit, replacing information technology is adequately direct forrard, though it tin be time consuming. It is recommended that you lot review a service manual specific to your vehicle when replacing the motor, as the methods used to detach car doors can vary from vehicle to vehicle.

one
Remove the interior door panel. Nigh interior door panels are held in place with plastic interior fasteners. You can remove these fasteners by pulling on them until they pop out of their holes. Interior panels may also be held on with metallic or plastic screws or even bolts.^[1]
- If y'all can't easily identify what kind of fasteners are on your door panel, refer to the vehicle's service transmission.
- Plow screws or bolts counter clockwise to loosen them, then pull the panel backward off of the door.
ii
Gently remove the plastic door cover. Beneath the door panel you will detect a thin, translucent layer of plastic. This comprehend protects the interior of the vehicle from whatsoever h2o that may splash into the door from above and below. Carefully pull the door off of the sticky portions that secure it.^[2]
- Try not to tear the cover as you volition need to reinstall information technology after replacing the window motor.
- Replacement covers can be purchased at your local auto parts store.
Advertisement
iii
Locate the window mounting bolts. Depending on the design of your door, in that location are a few different places the window mounting bolts may be, just information technology should be adequately apparent when looking into the door. Await for the bolts attaching the window itself to the mechanism that raises and lowers it.^[3]
- You may need to apply a flashlight to look into the service ports on the door.
- Different shaped doors will identify the bolts in unlike locations.
iv
Move the window if necessary to access the bolts. In some cases, you may need to heighten or lower the window in order to access the bolts. Turn the cardinal in the ignition of the vehicle without starting the engine to motility the window if need be.^[4]
- Raise or lower the window using the power window buttons if possible.
- If the motor is cleaved, you can force the window up or down past paw.
5
Remove the bolts while a friend supports the window. Employ the appropriate sized socket or open up ended wrench to remove the window mounting bolts, but enquire a friend to hold the window up as you do to prevent it from falling down once information technology's disconnected.^[5]
- You may be able to hold the window in place as you loosen the bolts yourself, merely it's dangerous.
- Dropping the window freely could result in the glass breaking.
6
Raise the window up into the door frame. Have your friend heighten the window up into the door frame as though you had rolled it upwardly usually. Enquire them to hold the window in place until you are able to secure it.^[6]
- Pressing one palm on each side of the glass will allow your friend to concord the window upwardly.
7
Employ masking tape to secure the window in place. With your friend holding the window upwards, pull off three or iv strips of masking tape that are each about a foot long. Stick the strips to the window on each side over the door frame to hold the window up while you lot work.^[seven]
- Once the window is secured with the tape, you lot tin have your friend permit go.
- Exist sure the tape will hold the weight of the window before your friend releases information technology.
Advertizing

ane
Remove the window regulator bolts. The window regulator runs the width of the interior portion of the door and moves back and forth in order to heighten and lower the window. Detect the bolts that hold the regulator to the door and remove them with a socket or open ended wrench.^[viii]
- Set the bolts bated someplace safe, where y'all will easily be able to determine which bolts were for the regulator.
- Exit the regulator laying within the door's interior for now.
ii
Locate and remove the window motor mounting bolts. The ability window motor is much smaller than the regulator, but should be located close by. In most applications, the bolts securing the motor to the door are the aforementioned size every bit the regulator mounting bolts. Remove them and set them someplace safety too.^[9]
- Even if the bolts have the aforementioned size caput, they may not exist the same length, so be sure to set up them aside separately from the regulator mounting bolts.
3
Disconnect the motor wiring harness connector. The power window controls adhere to the motor and regulator via a wiring pigtail connector. Press the tab downward to disconnect the pigtail so pull them apart to disconnect the motor.^[ten]
- Be careful non to suspension the tab that holds the wiring harness together.
- Pull the pigtail apart at the clip, not on the wires. Pulling on the wires could pull them out of the pigtail.
four
Remove the motor and regulator through the access port. With the pigtail disconnected, the ability window motor and regulator will no longer be connected to anything inside the door. Accomplish into the large access port and pull them each out.^[11]
- The two are connected, and so pulling one will remove them both.
- Exist careful not to damage the regulator if you are just replacing the motor.
v
Connect the regulator to the new motor. If y'all are only replacing the power window motor and not the regulator itself, you will need to disconnect it and connect it to your new ability window motor. Visually inspect the two to make sure the new motor matches the old one, so bandy the regulator.^[12]
- Unlike vehicles will use dissimilar methodology to secure the regulator to the window motor.
- Refer to the service manual for your vehicle if yous are unsure of how to disconnect the regulator.
Advertizement

1
Slide the new motor and regulator back into place. Insert the ability window motor and regulator dorsum into the primary service port in the door in exactly the contrary order that you lot removed them in when disassembling the door.^[13]
- Orient each component so the holes for the mounting bolts will line up with the holes in the interior of the door.
2
Supersede the mounting bolts. Hold each component in the advisable position as you return the mounting bolts that secure both the power window motor and the regulator. Thread each commodities in by hand first, then use a wrench to tighten them.^[14]
- If a bolt doesn't thread it properly, remove it and endeavor again to prevent cantankerous-threading them.
- The bolts don't have to be extremely tight, just tight plenty to foreclose them from vibrating loose as you lot drive.
three
Reconnect the electrical connector. Once the ability window motor and regulator are both mounted securely to the door, connect the wiring from the motor to the pigtail you disconnected previously. This will reconnect the ability window switches and power source.^[15]
- Be sure the connections fit together. If non, you don't have the right ability window motor.
iv
Remove the masking tape and lower the window back downward. Ask your friend to concur the window once more. Once they are in identify, remove the masking tape that is belongings the window upwardly in the door frame. In one case the tape is removed, your friend can lower the window back into the mounting subclass.^[sixteen]
- Make certain your friend has a grip on the window earlier removing the tape that secures it.
- Yous tin can use adhesive remover like Goo Gone on the window if the tape left any residue one time y'all are done.
v
Insert the window mounting bolts. Accept your friend hold the window in the correct place and then the holes in line up with the holes for the window mounting bolts. Once the window is in identify, thread the window mounting bolts in past hand, earlier tightening them with the wrench.^[17]
- Exist sure your friend holds the window in place until the mounting bolts are in identify.
- Have your friend let go gradually to ensure the bolts are holding the window properly.
vi
Reinstall the plastic liner and interior console. Once the window is mounted again, yous can reattach the plastic interior embrace, then reinstall the interior panel over the door. Insert the door mounting bolts or snaps to agree information technology in place.^[eighteen]
- Once the door is reassembled, reconnect the bombardment.
- Start the engine and test the window.
Advertisement

Add New Question

Question

If a regulator has a helper spring on it, practise I need to take the whole regulator out to secure the artillery, or can I supercede the motor while it is in the car?

Depending on the design of the vehicle, you will likely need to remove the regulator as well equally the motor when replacing it.
Question

Is the window regulator motor from a 2001 Ford Escape interchangeable with a 2002 Ford Explorer?

They might be. The best mode to know for certain is to bank check the role numbers for each and meet if they lucifer. If they do not, they are non interchangeable.
Question

Where is the fuse located?

The_general_s

Community Answer

Fuses are commonly in one of three areas: the engine bay, trunk expanse, well-nigh steering wheel.