How To Remove Tail Light Toyota Corolla

Toyota Corolla Tail Low-cal Bulbs Replacement Guide
How to change a burnt out rear plow signal or side marker light bulb in a 2022, 2022 and 2022 Toyota Corolla.

2022 Corolla Tail Lights
Open up Trunk Lid
Black Plastic Cover This automotive maintenance tutorial was specifically written to assist owners of the 12th generation 2019 (hatchback), 2022, 2022, 2022 (and probably also the 2023, 2024 & 2025) Toyota Corolla sedan in changing a burnt out rear turn bespeak light bulb or a rear side marker light bulb. (The OEM brake lights are LED bulbs that should last the life fourth dimension of the vehicle.)

Owners of other Toyota and Lexus vehicles such as the Camry, C-HR, Venza, Avalon, 86, Sienna, Tacoma, RAV4, Highlander, 4Runner, Sequoia, IS 350, RX 350, UX 200, GS 350, IS 300 and ES 350 may also find these DIY instructions to be helpful.

The compatible replacement calorie-free seedling function numbers are as follows: Rear Turn Signal # 7440NA (too known as WY21W) and Rear Side Marker # 2825 (also known as W5W).

If you'd like to accept brighter tail lights that will besides last much longer before burning out like the traditional incandescent bulbs, install some bister colored 7440NA LED and clear 2825 LED units.

The tools needed to remove the light housing and access the seedling sockets include a plastic pry bar tool, a 10mm socket and a 1/iv" bulldoze ratchet.

The first two steps are to open the trunk lid and movement to the side of the vehicle with the burnt out bulb.

Insert the bract of a pry bar tool under the black plastic trim cover on the inner edge of the tail light housing.

Pry Off Trim Cover
Trim Encompass Removed
Two Black Metal Bolts Gently pull off the trim encompass to release the two retaining clips.

Try to avoid using excessive forcefulness. The friction fasteners should popular off relatively easily.

Set the trim cover aside in a safe place.

Once the comprehend has been removed, you'll be able to see the 2 black metal bolts that secure the inner edge of the tail light housing in place to the rear corner of the automobile.

Loosen Counterclockwise
Remove Lower Commodities
Pull Off Tail Light Housing Loosen the two bolts by turning them in the counterclockwise management with the 10mm socket and a 1/4" drive ratchet.

Gear up the two bolts aside in a safety place.

The housing is nonetheless held in identify by a metal peg inserted into a grommet and a slot that slides over a pop rivet push button caput.

Advisedly pull the housing directly back off the motorcar.

If y'all have trouble remove the housing, endeavour very gently wiggling information technology back and along or upwards and downwards to loosen the two friction fasteners.

Light Housing Removed
1/4 Turn Counterclockwise
Rear Turn Signal Socket Turn over the tail light housing and residuum it on the bumper to access the bulb sockets.

To prevent from scratching the lens encompass or the painted bumper, place a towel in betwixt the ii surfaces.

The larger grey socket contains the rear turn signal light seedling.

Rotate the socket 1/4 turn in the counterclockwise direction before pulling it direct out of the housing.

Pull Out One-time Lite Bulb
Old Low-cal Bulb Removed
Push In New Calorie-free Bulb Warning - If the former lite bulbs were recently turned on, they might still be hot plenty to burn your fingers!

Gently pull the erstwhile lite seedling direct out of the socket.

If y'all take problem removing the quondam bulb, attempt wiggling it dorsum and forth while pulling it straight out.

Button a new number 7440NA (likewise known as WY21W) amber colored light bulb direct into the socket.

Make clean off the new incandescent light bulb with a newspaper towel and some rubbing alcohol.

If you lot'd like to have brighter rear plow signal lights, install some compatible replacement 7440NA LED units.

1/4 Turn Clockwise
one/4 Turn Counterclockwise
Rear Side Marking Bulb Re-insert the bulb socket into the housing and rotate it ane/4 plow in the clockwise direction to secure it in identify.

The smaller gray socket contains the rear side marking calorie-free bulb.

Rotate the base of the socket one/4 plow in the counterclockwise direction before pulling information technology straight out of the housing.

Pull Out Quondam Light Seedling
Push In New Low-cal Bulb
1/iv Turn Clockwise Pull the old miniature wedge base light seedling straight out of the socket.

Button a new number 2825 (also known as W5W) light seedling direct into the socket.

Clean off whatsoever grease or oil on the new seedling with a paper towel and rubbing alcohol. If there is whatsoever dirt or oil on the new bulb, it could create a hot spot and cause it to burn out prematurely.

If you'd like to have brighter rear side marker lights, install some uniform replacement 2825 LED bulbs.

Re-insert the socket into the housing and rotate it i/4 turn in the clockwise direction to lock it into place.

LED Brake Lite
Line Up Peg & Slot
Slide On Light Housing The 12th generation Corolla is equipped with LED brake lights (stop lamps) that should terminal the life time of the vehicle.

To supercede the light housing, concur it nigh the rear corner of the vehicle.

Line upwards the metallic peg with its corresponding plastic grommet and line up the slot with the pop rivet button caput.

Slide the tail light housing straight on to the vehicle.

Replace Two Bolts
Tighten Clockwise
Line Up Trim Cover Spin in the 2 bolts a few turns by hand in the clockwise direction to make sure they don't become cross threaded.

Tighten the bolts with the 10mm socket and a 1/4" drive ratchet until they are snug.

Push To Secure Clips
Close Trunk Lid
Examination New Light Bulbs Line up the black plastic trim cover.

Gently push on the cover to secure the two retaining clips.

Double check that the comprehend is securely attached before moving on to the side by side steps.

Shut the trunk lid to complete the chore.

To test the new tail light bulbs, have an assistant footstep on the brake pedal, plow on the parking lights (or headlights) and activate the hazard signals.

Tip - If y'all installed an LED bulb and it doesn't work, try removing it from the socket, rotate it 180 degrees and and then button information technology back into the socket. Some LED bulbs are "polarized" and volition only work when the "+" positive and "-" negative electrical contacts are in the correct orientation.

Don't forget to write down the seedling change in your car'southward service records.

Delight bank check out all of my 2020 Toyota Corolla DIY Repair & Maintenance Guides.

Source: https://paulstravelpictures.com/2020-Toyota-Corolla-Tail-Light-Bulbs-Replacement-Guide/index.html

Share this post